Forum Replies Created
March 6, 2018 at 9:27 pm #8290
I have a water fountain to install, and I need 6 more bricks of eco-earth. I also need to make some pools. I’m contemplating putting a 14″ hamster wheel in also.
I still need to do some trim work on the enclosure and make solid doors.
I’m also planning on putting an iso tank in the storage area below. The iso tank will have its own controller for temp and humidity and will slide out like a drawer.March 6, 2018 at 9:17 pm #8288
Well I’ve made some progress.
All the spray foam is covered with flex seal and coconut fiber.
Finished the enclosure.
Drilled holes in the top, for the ceramic heat emitter and hygrotherm controller.
Installed an 18″ Uvb fluorescent.
Hung up some silk vines.
Dropped about 250lbs of substrate in, and 4 gallons of dechlorinated water.
I’ve let the hygrotherm control the temp for a couple day now. So I can monitor fluctuations in temp and humidity. It’s seems to have stabilized at 84 degrees for the hottest area and 78 degrees for the coolest. Humidity has been going between 82% and 87%.
Attachments:You must be logged in to view attached files.January 12, 2018 at 11:22 am #7943
Sorry I haven’t been updating this thread. Work has been crazy, low interest rates make for busy carpenters, lol. I’ve made some progress, on the crabitat. I cut out all the little “caves”. I added a big branch and made a platform on the backside. I’m made a track for sliding glass doors. I’m using the terrarium cork background flats to make a “tree trunk” for climbing.
Attachments:You must be logged in to view attached files.November 30, 2017 at 12:10 am #7772
So this is a pic of the crabitat. I drew in where the substrate will be. I did some spray foam hides, but I think I’m going to cut them out.
I have egg crate screwed to the plywood as extra support for the sprayfoam. At $16 a for a 4’x2′ sheet, I used two sheets and only did the lower section. Seems to be on there pretty good.
I haven’t had time to pickup the material for the face frame or the trim pieces on the build yet. Maybe this weekend.
I’ve found Wal-Mart has the best price on great stuff spray foam. I’ve used about 6 can @ $3 a piece. I think I’ll need at least 3 more.
I’m also waiting on some cork bark, for the background, that I ordered from pet mountain and a few other odds and ends.November 29, 2017 at 4:16 am #7747
I contemplated the wood enclosure for a while, and how to deal with the moisture. I considered resins and epoxys, the kind they use for plywood aquariums, but it seemed too expensive.
Im feeling confident that covering the entire wood surface with spray foam will prevent any moisture damage, and increase the R-value. Adding a coat of the flex seal liquid over the top of the spray foam should be more than sufficient, to prevent moisture damage.
As to the flex seal being toxic. According to the FAQ on the flex seal website, the liquid is safe for plants and animals. I don’t believe the spray is safe though.November 25, 2017 at 1:09 am #7710
On to the plan.
I’m building a 6′ tall, 4′ wide, and 2′ deep unit. out of alder plywood. The bottom 2 feet will have a storage cabinet to hide all the crab supplies. the top 4 feet will be the crabitat.
The bottom of the crabitat will be 1.5″ thick to support the weight of the 10″ of substrate.
I’m using spray foam to create the hiding spots, and climbing surface. I will also use the spray foam to attach corkbark and a few pots for plants. I will then seal all the surfaces with clear flex seal liquid and press eco earth into that.
I have a 36″ full spectrum LED light, which should create plenty of light for the crabs and the plants, but I’m not positive. I could use some input here.
I have a 100w ceramic heat emitter and a thermostat control to regulate the temperature. Does this seem adequate and is a constant 80 degrees sufficient?
I need ideas on airflow also. I’m considering using 2 80mm computer fans with a thermostat to increase speed as the temperature rises.November 25, 2017 at 12:28 am #7708
Here is my current set up. Substrate is eco earth/playsand and is 4.5″ at deep end. I have a large fresh water and saltwater pool with air stones. temp is around 80 degrees during the day cycle and 75 during the night cycle. humidity fluctuates between 70% and 90%, but generally around 80%.
This setup is lacking substrate depth, climbing area, hidey holes, air flow, temperature variations, and proper lighting. The goal of this build is to make a more “natural” environment, to increase activity and overall health of the occupants.
If you see any other inadequacies, please feel free to point them out.